Once you have completed the preparation stage including measuring how much artificial grass you need, installing appropriate drainage (if needed) and taking out the natural grass layer, you will be ready to install your artificial grass lawn. This short article outlines the steps you need to follow to assist you to get the job done right, from laying the base, connecting joints and preventing weed growth.
Lay Gravel Base followed by Sharp Sand – If neccessary, use treated timber/timber stakes to set in an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber for good draining areas. Screw these timbers for the stakes leaving the stakes on the within the perimeter. If the Artificial Grass meet a concrete path, wall or decking, position the timber flush using the surface height and through using 10mm temporary fillet, pack the timber near to the wall leaving the room to enable you to tuck the Artificial Grass involving the timber as well as the adjoining material at a later stage.
Position the stakes up against the inner perimeter timber edging and hammer in the ground ensuring the stakes are slightly less than the timber edging. Next screw the timber stake towards the timber edging. With heavy clay soils we recommend laying a crushed stone surface as much as 3 inches. This will never be necessary for the majority of areas and only required in case you have a very high water table in which the ground holds water for a long time of energy after it rains. Next compact the ground employing a vibrating plate which can be hired from an equipment hire company. Make sure the perimeter is compacted and below the timber edging by 1 inch. Infill the perimeter with sharp sand and level utilizing a rake. Make sure the sand is level to the very top in the timber edging and compact again.
For good drainage areas spread a layer of sharp sand to blind on the soil. Next compact the earth utilizing a vibrating plate which can be hired from an equipment hire company. Ensure the perimeter is compacted and level with the timber edging. Should you put more operate in at this time, your Artificial Grass Lawn will appear better as a result.
Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails to the timber edging. This weed control geo textile membrane prevents any possibility of weed growth with the artificial grass drainage holes.
Roll out Artificial Grass – Lay the Artificial Grass within the desired direction working on the carpet rather than on the levelled base. Guarantee the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by a minimum of 4 inches. If the artificial grass meets a path or edge, and if you have laid the timber edging correctly as previously described, then the artificial grass can be wedged between. If joining, please ensure that the irrigation supplies thousand oaks is laid with all the pile running in the same direction on each piece. Lay the carpet on top of the sand rather than dragging it throughout the base material. To aid stop wrinkles or creasing it is advisable to allow 2 to three hours to settle before continuing with jointing and adhesive. Cut grass to shape employing a sharp Dolphin or Stanley knife or scissors.
Jointing – When jointing your outdoor carpet together, make sure the pile runs in the same direction. Cut off manufacturer’s edge strip (if present) and butt two edges together ensuring there are no gaps greater than 1mm involving the two carpet edges. The precision of the determines how visible the join is right after the completion. Fold back edges and position jointing tape (smooth side down) so that the edges of the carpet meet the tape when joined.
Adhesive – a) Apply the cartridge adhesive in a zig zag motion to the rougher side from the tape allowing one cartridge for each 3 linear metres. Reject carpet and press both edges to the wet adhesive, ensuring each piece marries up and has no overlap. As you are doing this with your fingers, mix the fibres together to conceal the join. When the whole length is in place and you are satisfied with its appearance it is required to walk along the join several times to activate the glue and bond the grass to the tape. Weigh down the seam to ensure good contact with the glue until it cures. The better care taken with all the operation the neater and tidier the joint is going to be.
b) If utilizing the 2-component multi-purpose adhesive, ensure thorough mixing of these two components before use. Apply adhesive for the rough side in the tape and spread evenly across a width of at the very least 20cm using if possible a notched trowel. Sufficient adhesive ought to be applied so that when the artificial grass carpet is pressed in to the adhesive, a transfer on the xggnvo backing is complete. Turn down carpet and press both edges to the wet adhesive, ensuring each piece marries up and contains no overlap. Ensure that the carpet will not crest on the seam and is holding flat within the bonded area. When the whole length is in place and also you are satisfied with its appearance it is required to walk along the join repeatedly to activate the glue and bond the grass towards the tape. Weight the seam to make certain good connection with the glue until it cures. The more care taken using the operation the neater and tidier the joint will be.
As you should endeavour not to put adhesive to the carpet small quantities of glue can be taken off from the artificial grass fibre using White Spirit as well as a small off cut in the artificial grass. Small quantities of cured glue can usually be removed. To avert this situation and the chance of injury to the artificial grass, care and precautions needs to be taken to avoid connection with the fibres all the time. When the artificial grass continues to be jointed and glued and you are pleased with all the levels screw the grass for the timber perimeter framework using galvanised screws at least of 12 inch intervals.
Spread Sand (Optional, based on Grass Selected) – When the artificial grass continues to be laid use silica sand, which is kiln dried and brush into carpet as you go. Each product may have sand infill but this really is only utilized to stabilise the carpet as well as at almost no time should the sand be visible. You need to get an even spread over the surface using a brush to formulate the depth in layers. Do not apply the sand in one application. Brush sand into pile soon after laying while the artificial grass is dry even though weather conditions are good. Brush vigorously up against the fibres of the carpet pile to encourage the tufts to stand upright. Putting the right quantity of sand in helps support the artificial grass to bed down, protects the fibres and also keeps them standing to give it the appearance of real grass.